Embrio Forum
»
Embrio Support
»
Programming with Embrio
»
Many Problems Of Communications Betweeen Arduino Nano And Pc.
Rank: Advanced Member
Groups: BetaUser, Registered Joined: 12/28/2015(UTC) Posts: 31
Was thanked: 18 time(s) in 18 post(s)
|
Dear Admin, I Have Many problems on communication with my custom software.....,I'm Trying to use lcd I2c and my Custom matrix led function...Many Times I get These Messages....Any Help??Thanks Lestroso... Quote: 16:33:31 There were no errors captured in the upload process, but Embrio isn't receiving connection data from the Arduino. If the correct port is selected, it could mean that there is a delay in a custom Arduino node which is slowing down the compiled Embrio program. Make sure you don't use the delay() function in custom Arduino nodes. 16:33:26 avrdude: 2686 bytes of flash written avrdude: 2686 bytes of flash verified 16:33:26 Bridge code uploaded. 16:33:26 Arduino upload process finished. 16:32:48 /C ""c:\Program Files (x86)\Arduino\arduino" --upload --verbose --port COM9 --board arduino:avr:nano "C:\Users\save\AppData\Roaming\Embrio\ArduinoCompile\ArduinoCompile.ino\" > output.txt 2>&1\" 16:32:48 Compiling connection program... 16:32:08 There were no errors captured in the upload process, but Embrio isn't receiving connection data from the Arduino. If the correct port is selected, it could mean that there is a delay in a custom Arduino node which is slowing down the compiled Embrio program. Make sure you don't use the delay() function in custom Arduino nodes. 16:32:03 avrdude: 2686 bytes of flash written avrdude: 2686 bytes of flash verified 16:32:03 Bridge code uploaded. 16:32:03 Arduino upload process finished. 16:31:18 /C ""c:\Program Files (x86)\Arduino\arduino" --upload --verbose --port COM9 --board arduino:avr:nano "C:\Users\save\AppData\Roaming\Embrio\ArduinoCompile\ArduinoCompile.ino\" > output.txt 2>&1\" 16:31:18 Compiling connection program... 16:30:34 There were no errors captured in the upload process, but Embrio isn't receiving connection data from the Arduino. If the correct port is selected, it could mean that there is a delay in a custom Arduino node which is slowing down the compiled Embrio program. Make sure you don't use the delay() function in custom Arduino nodes. 16:30:28 avrdude: 2686 bytes of flash written avrdude: 2686 bytes of flash verified 16:30:28 Bridge code uploaded. 16:30:28 Arduino upload process finished. 16:29:49 /C ""c:\Program Files (x86)\Arduino\arduino" --upload --verbose --port COM9 --board arduino:avr:nano "C:\Users\save\AppData\Roaming\Embrio\ArduinoCompile\ArduinoCompile.ino\" > output.txt 2>&1\" 16:29:49 Compiling connection program...
|
1 user thanked fasasoftware@gmail.com for this useful post.
|
|
|
Rank: Administration
Groups: Administrators
Joined: 12/11/2014(UTC) Posts: 661
Thanks: 1 times Was thanked: 109 time(s) in 104 post(s)
|
Does communication work with the built in input and output nodes?
When in connection mode the program running on the Arduino will be sending lots of commands like "upd:1:2", and once per second something like "inf:abcde". If Embrio isn't getting those messages, it assumes there's no connection and shows you that error message.
Is there anything in your custom node that would make the program run slow, like a call to delay?
After uploading a connection program, could you open a terminal in the Arduino IDE and see what kind of messages are coming across?
|
1 user thanked EmbrioAdmin for this useful post.
|
|
|
Rank: Advanced Member
Groups: BetaUser, Registered Joined: 12/28/2015(UTC) Posts: 31
Was thanked: 18 time(s) in 18 post(s)
|
Dear Admin, I see when there are something wrong with my custom node, i have putted sometime a call to delay, but i tryed with and without delays..but many times my custom program node fail... Perhaps, it's my fault.....but i see when the program is ok working the connection is good..say me the compiler... But many time , when i see my custom program working in theory, visuallly working...many times don't work in pratic... I love your software , but at first sight could be difficult, but when you start to understand the basics concepts....It very Great!!! Thanks again Admin, Lestroso
|
1 user thanked fasasoftware@gmail.com for this useful post.
|
|
|
Rank: Administration
Groups: Administrators
Joined: 12/11/2014(UTC) Posts: 661
Thanks: 1 times Was thanked: 109 time(s) in 104 post(s)
|
It mostly works but there are definitely a couple of bugs that were added recently. They are mostly fixed now, I'll post a new installer this weekend and hopefully your problems will be solved.
|
1 user thanked EmbrioAdmin for this useful post.
|
|
|
Rank: Administration
Groups: Administrators
Joined: 12/11/2014(UTC) Posts: 661
Thanks: 1 times Was thanked: 109 time(s) in 104 post(s)
|
The new installer should fix the issues you are seeing, please let me know if that's not the case.
|
1 user thanked EmbrioAdmin for this useful post.
|
|
|
Embrio Forum
»
Embrio Support
»
Programming with Embrio
»
Many Problems Of Communications Betweeen Arduino Nano And Pc.
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.